Home | About Us | Price Promise | Contact Us
Checkout | My Cart (Cart is Empty)  
Product Categories
STAINLESS STEEL TILES
BRASS & COPPER TILES
STAINLESS STEEL MOSAIC
MINI TILES
SPLASHBACKS
METAL FLOOR TILES
HAND & FOOT RAILS
STAINLESS WORKTOPS
DOOR & DRAWER FRONTS
PLINTHS St/St
BESPOKE MANUFACTURE
Site Information

 

 

 

Signup for our newsletter
Email Address :
Click here to unsubscribe
These unique tiles use the same installation methods as that of standard ceramic tiles, and would give a touch of luxury and elegance to any modern contemporary kitchen or bathroom. Used as a splashback the grained satin finish will complement any kitchen as well as matching any stainless steel cooker or hob.
 
IMPORTANT NOTICE: -
On the face of all our metal tiles there is vinyl protective cover to protect the finish during installation. Without this cover it is near imposable to grout without damaging the finish, when buying from other suppliers please make sure their tiles are protected.
 
Standard Range, 
Stainless Steel Tiles & Borders
 

Materials
Stainless Steel to BS304

Size
150 x 150 x 6mm
150 x 75 x 6mm
100 x 100 x 6mm

75 x 75 x 6mm
150 x 30 x 6mm

Standard Finishes
Grained Satin Stainless Steel
Polished Stainless Steel

Textured Finishes
Chequred Stainless Steel
Leather Stainless Steel

Pearl Stainless Steel



 

 

 


 
Cleaning Stainless Steel
 

Stainless Steel Grained
To keep stainless steel tiles clean simply wash with warm soapy water. For best results and to remove stubborn mark and to remove streaks, use a non-abrasive hard surface cleaner. Never use steel wool or abrasive compounds or materials.

Stainless Steel Polished
Require no more then a light dusting to keep them looking their best. For best results and to remove stubborn mark and to remove streaks, use a non-abrasive hard surface cleaner. Never use steel wool or abrasive compounds or materials.

 
Fitting Instructions
 

Metal tiles are manufactured to a unique design that allows installation using the tried and tested methods to that of a standard ceramic tile and being of the same thickness, therefore allowing both tiles to be used together.

INSTRUCTIONS

  1. Do not remove the vinyl covering from the tiles until installation is complete (see notes).
  2. Make sure all the tiles are the same batch numbers.
  3. Ensure that the fixing surface is clean and even.
  4. Apply standard tile adhesive with a notched trowel as per manufacturer's instructions.
  5. Set the tiles. (Metal tiles are self-spacing at 2.4mm).
  6. Grout the joints with a specific filler and clean any excess. (A rubber grouting tool is recommended)
  7. After the grout has set, seal with an appropriate grout sealant.
  8. When dry, clean and remove vinyl covering from the tiles.

CUTTING

Metal tiles will not score and snap like ceramic tiles but can be cut with any cutting tool designed to cut metal from HSS hack saw (32 TPI Minimum) or a tungsten carbide fine grit hack/jig saw blade to diamond impregnated circular wet saw all of which are available from good DIY stores. After cutting remove burr with a file. (Metal tiles may have sharp edges please take care)

NOTES

  1. Ensure a qualified electrician carries out all electrical work (Removal and replacement of light switcher and power points etc). All back boxes must be re-installed flush with top of tiles but not in contact with the metal face of the tiles.
  2. Where appropriate the vinyl covering will be clear or have lines to indicate the direction of the grain.
  3. Vinyl covering will only assist in protecting the surface of the tile during installation so do take care.
  4. Never hit or tap thetile into place as this may damage the tile.
  5. Due to the nature of metal materials it is inevitable that there will be some variation in colour and texture.
  6. Maximum continuous operating temperature 120C.
 
 
Metal Tiles Ltd 2000-2003
My Cart
Cart is Empty
Featured Products
 
Product Information
Price Promise
Why stainless steel
Stainless Steel Tiles Spec
Brass & Copper Tiles Spec
Gallery

Postage rates
Currency Converter
F.O.C.
TRADE ENQUIRIES
Standard Finishes

finishes

Search
Advanced Search